Easy Answers To Your Tough Plumbing Questions

Are you doing your own plumbing for the first time? You probably don't even know where to start. It's no secret that doing your own plumbing for the first time can be a bit overwhelming. Below are some tips that can help to make maintaining your own plumbing a bit smoother.



Avoid frozen pipes this winter! Keep a small trickle of water dripping from faucets, and wrap your uninsulated pipes with foam or newspaper. If possible, keep the doors open between unheated and heated rooms. In an unheated area such as a garage or laundry room, keep a small heater next to the pipes. Remember to do this before the first cold snap hits.

To winterize Suggested Looking at that will sit unused during the winter months, you must completely drain all of the pipes. After turning off the main water supply, let all of the water drain from the faucets, toilets, and water heater (turn off the gas). Add a quart of antifreeze to sinks and the tub to prevent water from freezing in the drain trap.

Do not pour grease or oil down any of your household drains. Put them in containers and place in the fridge until they are solid, then throw them away. If you pour them down the drain, they can solidify in cold pipes. These solid masses will clog your pipes and are very difficult to remove.

During the winter, preventing frozen pipes when you live in a small dwelling can be something good to know. Frozen pipes will not only stop your flow of water but can crack and damage pipes. By running a little water out of every faucet during the coldest parts of the day, you can avoid this.

Unclog drains with ease. Try using a plunger and drain cleaner, as your clog may simply be a build-up of hair and debris. If this doesn't work you may have to clear the drain with a snake. Feed the snake into the drain line as far as it will go. Turn the crank gently, which will help to loosen the clog. Remove the snake, and run water down the drain to see if the clog has been removed. You may have to use the snake a couple of times, before the clog is cleared so don't give up!

Many people deal with clogged toilets. However, if your toilet will not flush every time, the water rises to the top, and there is bubbling effect occasionally, this can be due to a much deeper blockage in the main pipe. The main pipe must then be cleaned in order for your toilet to work properly.

Drain the sediment from the bottom of your hot water heater twice a year to keep the hot water heater working at its optimal levels. Simply open the drain valve and allow the water to run out into a bucket until the water runs clear. Then close the drain valve.


To avoid sediment buildup, drain gallons of water from your water heater to flush any corrosion. This will help your heater to run more efficiently therefore saving you regular energy costs. Make sure to read your heater's instructions before attempting this, and do this periodically to make sure that your heater is running as well as it can.

Before you can fix a toilet that does not flush properly, it is important that you find out what is causing the problem. Depending on what the problem is, you may be able to fix it yourself. However, more complicated toilet flushing problems may require the services of a plumber.

Do not, under any circumstances, put lemons down your disposal. Although the lemon smell will give your disposal a great smell, its acid can corrode the metal parts in it. Instead, use products that are made specifically for this use. You can purchase these products at most hardware stores or wherever cleaning products are sold.

Make sure that you avoid throwing fats down the drain after you clean up your meal. Fats can solidify over time which can cause a drainage problem and corrupt your water flow. Throw out Suggested Looking at and different types of cooking oils in the garbage after you finish with your meal.

Protect you plumbing pipes! If you live in an area which has cold winters and are leaving your home for an extended amount of time, protect your plumbing while you are gone! Shut off the main water valve! Drain the system of water by opening the faucets at the highest and lowest points of the house. Also, make sure that you have left some heat on in the house! Set the thermostat to at least 55 degrees Fahrenheit.

If you have problems with a slow drain, there are easier things you can do other than removing the pipes to clean it. There are certain tools made just for this purpose that you insert into the drain to loosen the clog so it washes away or grab it and remove it completely.

While it might help to conserve a bit of water to not flush the toilet after every use or only under certain conditions, regularly flushing toilets can help keep water moving in pipes and prevent freezing. The same holds true for letting water run in sinks as well. If you have rarely used bathrooms in your home, make it point to to flush the toilets and run the faucets on a regular basis.

To avoid water damage to walls in the kitchen, make sure all seams in your counter tops and back splash are properly sealed using a waterproof silicone. Silicone will dry out over time, crack and shrink and should be replaced once every three years. Keeping your silicone in good shape will keep kitchen spills where they belong and not running down the walls.

If attempting a plumbing repair yourself, be sure and have plenty of buckets on hand to catch spilling water. While you may have turned off the water supply, there is always some water left in the pipes and the larger the home and more extensive the plumbing system, the more water you may encounter.

Educate everyone in your household on how to turn off the main water supply, as well as the individual water supplies in bathrooms and other areas of your home. Everyone needs to learn how to cease water flow that could cause flood damage. They can help you shut off the water, and stop the flow if they have already been taught how to do it.

If one of your pipes is leaking, you can fix it easily. Drain the water from the pipe by shutting off your main valve and open the closest faucets to drain the remaining water. Clean up the pipe from corrosion with sand paper and apply soldering flux. Heat the pipe with a torch and apply new solder. Repeat until the leak stops.

You know what can cause that hammering noise, plus a lot more plumbing information. You just saved yourself a lot of money if any of those issues became unbearable or resulted in broken parts. Take time to read back over this article periodically to make sure that you are on top of your plumbing skills.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Easy Answers To Your Tough Plumbing Questions”

Leave a Reply

Gravatar